Posts Tagged ‘Plumbing Maintenance’

« Older Entries

Doylestown Plumbing Tip: Sump Pump Maintenance is Easy in the Spring

Monday, April 30th, 2012

For those of us who own sump pumps in Doylestown, their maintenance is one of the most important things to make a little time for on a regular basis.  If a sump pump is not working properly it could mean flooding of a home or office building that sits below the water table level, or that had a basement waterproofing system in place.  Flooding can mean excessive damage to not only the basement, but to any other lower floors, and even foundation damage which will all then need to be repaired or replaced completely.  With such simple precautionary steps as performing a few quick maintenance checks it is easy to keep that sump pump running properly without such damage.  A good time to go about sump pump maintenance is during the springtime prior to the rainy season when the weather changes once again and other areas of the home or building are being checked as well.

  • For electric sump pumps: Ensure the sump pump is plugged into a working outlet, and that the cord is in good shape.  Due to the damp, the breakers on these outlets can trip more easily, which then shuts off the sump pump.  This is a simple fix as the breaker just needs to be reset.
  • For battery powered sump pumps: replace the battery as often as is recommended by the manufacturer.  On back-up battery powered pumps, replace the battery every two to three years.
  • Check that the sump pump is standing upright.  Since sump pumps vibrate they can fall to one side, which can jam vital parts, causing it not to activate properly.  While upright, all working parts should be free to move as necessary.
  • Pick up submersible pumps to clean the grate on the bottom.  Ensure that there are no small stones in the grate which could block the inlet or damage the pump.
  • Check that outlet pipes are tightly joined together, check that their outlet is at least twenty feet from the foundation of the home or building, and that when the sump pump is on it is actually removing water through the pipes.
  • Clean the vent hole in the discharge pipe, remove any debris which was stuck in it.

Besides performing maintenance on your Doylestown sump pump annually, it is good to check it again after heavy rains to ensure that it is still removing water properly.  Also check it after longer dry spells by dumping a bucket or two of water near the machine to make sure it starts up automatically and that it drains efficiently.  While most new models have indicators which alert you when the pump is not working properly, it is still good to physically check the machine periodically to ensure it is running properly.  With proper sump pump maintenance your sump pump will give you great service for a long time, so give Resolve Rooter a call today if you would like to schedule an appointment!

Tags: , , , , , , , ,
Posted in Services | Comments Off

Radnor Plumbing Repair Tip: Common Sump Pump Problems

Friday, January 27th, 2012

The sump pump in your home is an important piece of equipment that pumps out excess groundwater, which prevents flooding hazards in basements and water damage to your Radnor home. If the pump stops working or won’t shut off, you can usually solve the issue yourself. During times of heavy rain and potential flooding, it’s best to check your pump on a daily basis to make sure it’s running properly.

You can maintain your pump by having it inspected by a professional plumber, and keeping the pump clean and the well free of debris. Feel free to call Resolve Rooter if you have questions about how to maintain a sump pump, or to make an appointment for an annual inspection and professional cleaning.

Most issues can be repaired easily and without the help of a plumber. Here’s a troubleshooting guide to help you solve minor issues with your pump.

Check for Electrical Problems

Always check to make sure the sump pump is fully plugged in and that there aren’t any fuses that have burned out. If there is standing water in the basement, you should take extra precautions when handling any electrical equipment, even a plug. Call a plumber or electrician for advice if you have any safety concerns.

Check the Float Switch

Just like the float in a toilet tank, the float attached to the side of your sump pump acts as a guide for turning the pump on and off. This is called the float switch, and it usually has a large bulb or other floatation device attached to a metal arm. This float detects the water level inside the well, and it turns the pump on when the water reaches a certain height in the well.

If the pump is plugged in and there are no blown circuits, move the float switch up and down to see if it will turn the pump on. Debris can get trapped underneath the float causing it to stick. If the motor is constantly running, this switch may be stuck in the “on” position if debris is lodged underneath it, or if there’s substantial corrosion.

You can actually move the entire pump around to change the position if there’s no apparent debris causing the issue. Sometimes the pump gets shifted around slightly, and the float switch cannot work properly if the pump isn’t plumb or level. Be careful not to move it too much, since it could damage the drain line attached to the pump motor.

If your motor is constantly running, and none of these steps work, the motor could overheat and stop working. Unplug the pump while you’re investigating the problem, and if none of these steps work, call a professional plumber.

Check for Clogged Filters

In addition to causing issues with the float switch, debris trapped in the screen can also cause the motor to overheat or shut down. If your filter is dirty, try to get out as much of the debris as possible, but if this doesn’t solve the issue, you could have a clogged drain line. In this case, you will need to call a professional plumber to snake out the line.

Preventative Maintenance Tips

You can prevent issues with the sump pump in your Radnor home with a few preventative maintenance tasks. Keep debris from falling into the well as much as possible, and clean out any particles that could clog the screen or affect the operation of the float switch. Occasionally inspect the pump and well for any corrosion or other concerns. If you are comfortable with the operation of your pump, drain and clean the entire well and pump at least once a year.

Lastly, call a qualified technician at Resolve Rooter for a yearly sump pump maintenance visit.

Tags: , , , , , , , ,
Posted in Services | Comments Off

Clinton Plumber’s Tip: Why Sump Pump Maintenance is Important

Friday, January 13th, 2012

Keeping the sump pump clean in your Clinton home has many benefits. Not only does a clean sump pump run more efficiently, which lowers your energy bills, but it also helps prevent malfunctions. The sump pump in your home pumps out excess groundwater that could potentially flood your basement and cause major water damage and mold growth.

To prevent flood damage in your home, make sure your sump pump well is free of debris and that the pump it is maintained regularly. Call Resolve Rooter any time if you have questions about how to maintain sump pump or to have it professionally cleaned and inspected. Here are some specific reasons why a clean sump pump is important.

Float Switch Malfunctions

Most submerged sump pump models have a floater or similar device that detects the water level inside the well. Once the water table reaches a certain point, the float switch turns the pump on. If debris or dirt gets trapped underneath the switch, it can get stuck in the “on” position, which causes the motor to run constantly and potentially overheat.

Clogged Filters

Most filters in sump pumps are designed to allow smaller particles through, but larger pieces of debris can clog the system and cause it to shut down. An overheated motor or tripped circuit could result from a clogged filter because the motor has to work harder to pump out the water. If you aren’t sure how to check the filter for debris, call a professional plumber for advice.

Preventative Maintenance Tips

Try to keep debris from falling into the well, and clean out any large particles that you can see in the water. Occasionally fill the well all the way with a hose and test the floater switch to make sure it’s working properly. At least once a year, hire a professional plumber to drain your well and clean the inside of the well and the pump. Your plumber will also inspect the pump to make sure it is in good working condition.

You can help maintain the sump pump in your Clinton home simply by keeping it clean!

Tags: ,
Posted in Services | Comments Off

Easy Drain and Sewer Maintenance: Some Pointers from Watchung

Monday, January 2nd, 2012

When it comes to your Watchung home’s plumbing, one of the most important things you can do is perform regular drain and sewer maintenance. Those pipes are vital to maintaining a steady flow of waste water out of your home – if something goes wrong, you’ll regret not fixing it earlier. Here are some easy strategies for maintaining your drains and sewer lines:

  • Avoid Unflushable Items – Some items are designed to be flushed down the toilet. Everything else is not. If something isn’t specifically designed to go down your toilet, don’t put it down there. This includes paper towels, napkins, any kind of food, floss, or hair, and anything else that should go in a garbage can. Toilets may seemingly whisk everything away in one flush, but a lot of that stuff can get stuck on its trip to the sewer.
  • Clear Drains Weekly – You can’t clean your sewer line without professional help, but you can do your best to keep drains clear on their way out. Use boiling hot water and lemon juice or a mixture of baking soda and vinegar once a week to clear out the drains of any excess build up. Also, avoid putting any grease or other gunk down the drain that might stick to food particles and clog the drains.
  • Have Slow Drains Inspected – If a drain in your home slows down significantly, have it inspected. It might be a bit of hair stuck in a trap somewhere, or it could be your sewer line starting to clog. It’s better to know now than to wait and fall victim to a much larger problem in weeks or months.
  • Use Drain Strainers – Don’t let anything go directly down the drain. Use strainers to block food, hair or other stuff from getting into the sink or bathtub drains. Hair in particular, when mixed with grease or soap can become a glue-like substance in your drains.

Most drain and sewer maintenance is preventative and common sense. Pay attention to the effects your actions have on the water lines leaving your house and you can greatly reduce the risk that something goes wrong in the future.

Tags: , , , , , , ,
Posted in Services | Comments Off

Happy Halloween!

Monday, October 31st, 2011

Happy Halloween! Candy and costumes make any day fun; we hope you have a fantastic time trick or treating! Remember to be safe this holiday, and don’t forget it is time to start thinking seriously about fall maintenance for inside and outside your house. A quick tune up of your plumbing system will save you some trouble during this upcoming holiday season!

Tags: , ,
Posted in Services | Comments Off

Sump Pump Maintenance: Some Pointers from Stroudsburg

Friday, October 28th, 2011

A good sump pump is the only thing standing between you and a basement full of water, so it makes sense to implement a good maintenance plan for your pump. A lot of Stroudsburg homeowners don’t even think about their sump pumps, however, probably because they are buried out of sight, but the only way to know for sure that it will work when you need it most is to keep it in good operating condition. Here are some tips to help you do just that:

  • Check the GFCI – Your sump pump should be plugged into a Ground Fault Circuit Interrupter (GFCI). This is a special outlet that keeps the system from getting waterlogged. If it gets damp, it shuts down, turning off your sump pump. Unfortunately, GFCIs can be faulty or break, so check it regularly to make sure it is always on.
  • Upright Operation – If you have a standing sump pump, make sure it stays upright and doesn’t fall over when operating. These things can move a lot and if they do fall over, they may not pump properly.
  • Test it Regularly – Pour water into the sump pit when empty to make sure it will work when needed. Most people who need emergency service could have pinpointed the problem weeks or months earlier if they had known the system was broken.
  • Check the Outlet Pipes – Check the outlet pipes regularly for leaks or damage. If they start leaking back into the foundation, they can cause damage or leakage into the basement.
  • Clean the Grate – Submersible pumps are often left to sit in their pits for months or even years without cleaning. At least once a year, remove the sump pump from its pit and clean away any gunk that’s built up. Stones or debris in the pump can break the motor if left unchecked.

A good sump pump is all that stands between your home and a boat load of water whenever it rains. To keep your home clean and dry, check your pump often and if necessary, call someone for routine maintenance.

Most of the problems that pop up with sump pumps can be avoided entirely if they are maintained on an annual basis. Sometimes you may need to call a professional for advanced cleaning or part replacement. If so, try and do so before the raining season starts.

Tags: , , , , , ,
Posted in Services | Comments Off

Why It’s Important to Think about Plumbing: A Tip from Union

Monday, October 17th, 2011

If you’re like most people in Union, your plumbing is usually the last thing on your mind. Until something goes wrong, that is. And it’s pretty much guaranteed that you’ll have a clogged drain or leaky pipe in your home sooner or later. But while some plumbing problems are certainly unavoidable, there are quite a few things you can do to help keep them to a minimum and avoid larger plumbing emergencies later on.

Professional Checkups

For one thing, it’s a good idea to have your plumbing system checked by a professional every year or two. They can make sure that no roots interfere with the pipes in your yard and that things are generally flowing smoothly throughout the system. A professional inspection will also uncover any leaks, cracks or partial blockages that you may not have realized were there but that could cause significant damage later on if not dealt with promptly.

Do It Yourself Maintenance

In addition to professional inspections, though, there is some maintenance you can do on your own. For instance, every season brings new challenges for your home plumbing. Many people know that there are dangers associated with freezing pipes in the winter, but did you know that there are things you can do all year round to help your plumbing work better?

Fall is the best time of year to start disconnecting outdoor faucets and checking them for leaks. If you take these steps before the really cold weather sets in, you’ll be able to get necessary repairs done well before freezing outdoor temperatures become a problem.

This is also a good time of year to check for proper insulation around pipes and to make sure your water heater is tuned up and ready to go for the winter. Sure, you use it all year round, but the colder it is outside, the harder your water heater has to work all winter.

Once spring rolls around again, there are plenty of other tasks you can take on to ensure the continued healthy functioning of your plumbing. For instance, you should check all of your outdoor drains and gutters to see that they’re clear of debris that could have built up during the winter. You can also flush out your water heater again to clear whatever’s accumulated over the winter and check any pipes and faucets for problems that may have developed during the cold months.

Tags: , , , , ,
Posted in Services | Comments Off

Is There REALLY Such a Thing as Plumbing Maintenance? A Tip From Bethlehem

Wednesday, October 12th, 2011

Because it is so specialized and can lead to big messes if handled improperly, home plumbing is sometimes neglected among routine areas of maintenance in your Bethlehem home. This is a mistake, however, as there are some routine tasks that should be performed on plumbing systems, such as:

  • Remove rust, calcium and lime deposits from the water heater
  • Cleaning the aerators
  • Clearing drain lines
  • Sharpening disposal blades

Some of these are simpler than others, but for the most part, unless you are a very savvy homeowner, they should be done by a licensed plumber. Even if you are not up to doing your own plumbing work, there are still plenty of routine things you can do in order to detect potential problems and see if further work is needed.

In the Bathroom

  • Unscrew the showerhead and look for deposits of lime, calcium, rust and other minerals.
  • Run water down shower and tub drains for signs of slow drainage.
  • Inspect the shower/tub for cracked tiles, which can be signs of leakage beneath the surface.
  • Flush each toilet with the tank lid off to make sure they are flushing properly and all parts are working.
  • Examine all caulking for cracks, gaps or peeling.

In the Kitchen

  • Turn on the faucets. See if water leaks out of the knobs, handles or elsewhere.
  • Have leaky faucets fixed right away.
  • Look beneath the sink for signs of leakage from the exposed drain pipes.

Elsewhere around the House

  • Take a look at the flame and burner chamber of your water heater. A yellowed flame may mean the fuel jets need to be cleaned. Make sure the chamber is free of rust and other small debris.
  • Inspect the washing machines hoses for loose joints, cracking or holes.
  • Look for mold and mildew throughout.

Next Steps

If you find any troublesome issues during this inspection, it is time to call in a professional to get them fixed right away. Doing this simple walkthrough once to twice a year can help prevent plumbing disasters before they happen.

Tags: , , , , ,
Posted in Services | Comments Off

The Do’s and Don’ts of Clogged Drains: Some Advice From Scranton

Monday, October 10th, 2011

Clogged and slow drains can be a real bummer in your Scranton home. Water standing in the kitchen sink is gross, and no one likes to shower with the tub gradually filling around their feet. Calling a plumber when the clog gets out of hand is easy enough, but it’s time consuming. Plus, it means having to do without whatever water source that drain is involved with until a plumber can get there to fix it.

The best solution, then, is to prevent clogs from forming. With proper use, some brief regular maintenance and a few tricks, most clogs can be stopped dead in their tracks before becoming a problem. Follow these guidelines and you may never need to make that emergency plumber call again.

Don’ts

First of all, there are some things you just shouldn’t do to your drains and pipes. These things can quickly lead to clog buildup, so avoid them:

  • Don’t pour liquid grease, such as bacon grease, down drains. It can solidify in the pipes and cause a clog.
  • Don’t flush anything down the toilet that is not designed to be flushed.
  • Avoid using bleach or other chemicals to clean tubs, sinks and drains. Particles from these cleansers can build up to cause clogs, or even erode pipes.

Do’s

Even with best practices, no drain will remain completely clean. However, a little proactivity can stop everyday residue from accumulating and forming a nasty clog. Try some of these maintenance tips to keep things running smoothly:

  • Use a screen, guard or trap. These can catch food, hair and other debris which would otherwise wind up sitting in your pipes.
  • Clean sink and drain stoppers regularly. Debris can get trapped on and under the stoppers, just waiting to break loose and cruise into the drain to cause a clog.
  • A few times a year, stop up your sinks and tub, fill them up all the way, then let them drain. The pressure and volume of the water will help shake loose deposits in the pipes.
  • Once a month or so, carefully pour boiling water down the drain to dislodge stubborn deposits. You can also do this any time you notice a drain is starting to run slow. Vinegar is also effective.

It really can be as simple as that to keep your drains clear and avoid using nasty chemicals or shelling out big bucks to a plumber in an emergency.

Tags: , , , , , ,
Posted in Services | Comments Off

How to Prevent Bathroom Water Damage: A Guide From Deptford

Wednesday, October 5th, 2011

Water damage. Even the mere mention of potential damage from excess water in your Deptford house is enough to send a chill down your spine. However, there are a number of things you can do to avoid such damage, especially with your bathroom plumbing.

The Bathtub

The biggest single contributors to water damage are the shower and bathtub, where gallons upon gallons of water are distributed every day. You can minimize damage by doing the following:

  • Tiles – Check for missing or cracked tiles and replace them immediately. Supplement the tiles with grout that is properly sealed and check for any potential leaks.
  • Keep it Dry – There is a lot of water in your bathroom. Keep it off the floor by drying it up after a shower, hair washing or any other moisture producing activity in the bathroom. Make sure you minimize the risk of excess water by placing bathmats on the floor outside your shower.
  • Exhaust Fan – Water builds up in a bathroom because there is no moving air. Humidity can be just as damaging as actual wetness, especially if it settles in cooler temperatures. To avoid this happening, install an exhaust fan attached to the light switch to draw out any moisture after a shower.

Sinks and Fixtures

  • Check Under the Sink – Look under the sink and make sure there are no drips from the faucet and no leaks from the trap. You may simply need to check and clean the trap once every month or so.
  • Seals – Check sink seals on a regular basis for cracks or leaks and replace them when necessary.
  • Speed of Drainage – If the sink drains slowly, the drain may be clogged. Check the trap and if that doesn’t help, pour a mixture of vinegar and baking soda down weekly.
  • Upgrades – Upgrade your fixtures to save water. Toilets eat water to the tune of 40% of your annual consumption and your shower head can be made almost twice as efficient without cutting into your comfort level. If you notice a drip, crack or leak from any of these devices, simply upgrade them and you’ll save a lot of water (and reduce how much of it could leak if a problem occurs in the future).

There are a lot of ways to avoid water leaks in your bathroom. Keep a close eye on things and it will be much easier than if you waited for a full blown problem to develop. If you have any concerns about water damage in your house, contact your local plumber.

Tags: , , , , , ,
Posted in Services | Comments Off

« Older Entries